GETTING STARTED WITH PLUMBING BASICS WHEN INSTALLING A BATHTUB

Getting Started with Plumbing Basics When Installing a Bathtub

Getting Started with Plumbing Basics When Installing a Bathtub

Blog Article

Call Today

The article listed below pertaining to Installing A Bathtub is relatively enlightening. Try it and draw your own findings.


How to Install a Bathtub
Installing a tub isn't specifically brain surgery, but it does require solid plumbing, woodworking, and in some cases, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably hard task. If the old bathtub is conveniently available, the job can move immediately; if you need to open a wall surface to get rid of the old bathtub as well as position the new bathtub, the task is a lot harder. In either instance, the task is within a house handyman's skills, although you will require an assistant to leave the old tub and embeded in the new one. Ensure you have actually certified yourself for the work as well as fit attempting it. Instead of hiring a specialist to take over a halfway-completed task, it is better to take into consideration utilizing one prior to you begin. Opportunities are you might require a specialist plumber to make tube connections.
This write-up will aid you mount a new tub in your bathroom if you have currently bought a new tub as well as don't need to transform the plan of your previous supply of water pipes.
Your tools and product checklist should consist of the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Removing Old Taps


    If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the supply of water. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the limited gain access to that is usually the case.
    Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a fabric prepared for the remaining water that will come from the pipes. As soon as the supply pipelines have actually been gotten rid of, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this process. When the faucets have been removed, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
    Before proceeding to fit the new faucets, compare the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.

    Fitting New Taps


    If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end offers a connection to the existing supply pipes.
    If you require to fit a monobloc, after that you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washing machines are in place in between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the faucet is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap connectors. The former kind must be linked to the tap ends first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.

    Setting up the Bathtub


    Using both wooden boards under its feet, put the bathtub in the needed position. The wooden boards are useful in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
    The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the bathtub till the spirit level reviews level.
    To install faucets, fit the bottom of the furthest adaptable tap port to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
    Activate the water system and inspect all joints and also new pipework for leaks and also tighten them if necessary. Load the bathtub as well as additionally examine the overflow outlet and also the typical electrical outlet for leaks.
    Ultimately, repair the bath paneling as described in the manufacturer's user's manual. Tiling as well as securing around the bath tub must wait till the bathtub has actually been used a minimum of once as this will certainly resolve it into its final placement.

    Preparing for the Installation


    First of all, the supporting frame provided with the bathroom must be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps system to prevent pressure on the tub.
    Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the provided washing machines.
    Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final position.

    Tiling Around the Bath tub


    In the location where the bath fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to break an inflexible seal, creating the water to penetrate the wall surface in between the bath and also the tiling, leading to issues with wetness and feasible leaks to the ceiling below.
    You can choose from a range of coloured sealers to blend in your fixtures and installations. They are sold in tubes and cartridges, and also can securing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill up the tub with water prior to securing, to allow for the movement experienced when the tub remains in use. The sealer can split relatively very early if you do not think about this movement before sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the market. It is advisable to fit the tiles utilizing waterproof or waterproof glue and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    As an avid person who reads on How to Install a Bathtub Yourself, I assumed sharing that information was smart. Liked our post? Please share it. Help somebody else discover it. Thank you so much for your time spent reading it.


    Burst pipe? Phone!

    Report this page